Open Access

The cubic Laves-phase aluminides REAl2 with RE = Sc, Y, La, Yb and Lu were prepared from the elements by arc-melting or using refractory metal ampoules and induction heating. They all crystallize in the cubic crystal system with space group Fd[3 with combining macron]m and adopt the MgCu2 type structure. The title compounds were characterized by powder X-ray diffraction and spectroscopically investigated using Raman and 27Al and in the case of ScAl2 by 45Sc solid-state MAS NMR. In both, the Raman and NMR spectra, the aluminides exhibit only one signal due to the crystal structure. DFT calculations were used to calculate Bader charges illustrating the charge transfer in these compounds along with NMR parameters and densities of states. Finally, the bonding situation was assessed by means of ELF calculations rendering these compounds aluminides with positively charged REδ+ cations embedded in an [Al2]δ− polyanion.

Self-healing nanocomposites can be generated by organic functionalization of inorganic nanoparticles and complementary functionalization of the polymer matrix, allowing reversible interactions between the two components. Here, we report on self-healing nanocomposites based on ionic interactions between anionic copolymers consisting of di(ethylene glycol) methyl ether methacrylate, sodium 4-(methacryloyloxy)butan-1-sulfonate, and cationically functionalized iron oxide nanoparticles. The materials exhibited hygroscopic behavior. At water contents < 6%, the shear modulus was reduced by up to 90%. The nanoparticle concentration was identified as a second factor strongly influencing the mechanical properties of the materials. Backscattered scanning electron microscopy and small-angle X-ray scattering measurements showed the formation of agglomerates in the size range of 100 nm to a few µm in diameter, independent of concentration, resulting in the disordering of the semi-crystalline ionic polymer blocks. These effects resulted in an increase in the shear modulus of the composite from 3.7 MPa to 5.6 MPa, 6.3 Mpa, and 7.5 MPa for 2, 10, and 20 wt% particles, respectively. Temperature-induced self-healing was possible for all composites investigated. However, only 36% of the maximum stress could be recovered in systems with a low nanoparticle content, whereas the original properties were largely restored (>85%) at higher particle contents.

Nb2O5 has been explored as a promising anode material for use as lithium-ion batteries (LIBs), but depending on the crystal structure, the specific capacity was always reported to be usually around or below 200 mAh/g. For the first time, we present coarse-grained Nb2O5 materials that significantly overcome this capacity limitation with the promise of enabling high power applications. Our work introduces coarse-grained carbide-derived Nb2O5 phases obtained either by a one-step or a two-step bulk conversion process. By in situ production of chlorine gas from metal chloride salt at ambient pressure, we obtain in just one step directly orthorhombic Nb2O5 alongside carbide-derived carbon (o-Nb2O5/CDC). In situ formation of chlorine gas from metal chloride salt under vacuum conditions yields CDC covering the remaining carbide core, which can be transformed into metal oxides covered by a carbon shell upon thermal treatment in CO2 gas. The two-step process yielded a mixed-phase tetragonal and monoclinic Nb2O5 with CDC (m-Nb2O5/CDC). Our combined diffraction and spectroscopic data confirm that carbide-derived Nb2O5 materials show disordering of the crystallographic planes caused by oxygen deficiency in the structural units and, in the case of m-Nb2O5/CDC, severe stacking faults. This defect engineering allows access to a very high specific capacity exceeding the two-electron transfer process of conventional Nb2O5. The charge storage capacities of the resulting m-Nb2O5/CDC and o-Nb2O5/CDC are, in both cases, around 300 mAh/g at a specific current of 10 mA/g, thereby, the values are significantly higher than that of the state-of-the-art for Nb2O5 as a LIB anode. Carbide-derived Nb2O5 materials also show robust cycling stability over 500 cycles with capacity fading only 24% for the sample m-Nb2O5/CDC and 28% for o-Nb2O5/CDC, suggesting low degree of expansion/compaction during lithiation and delithiation.

Various food supplements for silicon uptake were compared in terms of their structures and chemical compositions. In particular, we analyzed the silanol group content, which can be an indicator of the uptake of the siliceous species in the human body. We analyzed the commercial products Original Silicea Balsam®, Flügge Siliceous Earth Powder, Pure Colloidal Silicon, and BioSil® by applying various methods such as FTIR, 29Si NMR, and TGA. The Si-OH group content of the samples containing pure silica was the highest for the Original Silicea Balsam followed by the Pure Colloidal Silicon. The siliceous earth powder revealed the lowest content of such groups and the densest structure. BioSil® contained a considerable concentration of organic molecules that stabilized orthosilicic acid. The study may help to understand the silicon uptake behavior of different food supplements depending on their chemical structure.

Molybdenum carbides, oxides, and mixed anionic carbide–nitride–oxides Mo(C,N,O)x are potential anode materials for lithium-ion batteries. Here we present the preparation of hybrid inorganic–organic precursors by a precipitation reaction of ammonium heptamolybdate ((NH4)6Mo7O24) with para-phenylenediamine in a continuous wet chemical process known as a microjet reactor. The mixing ratio of the two components has a crucial influence on the chemical composition of the obtained material. Pyrolysis of the precipitated precursor compounds preserved the size and morphology of the micro- to nanometer-sized starting materials. Changes in pyrolysis conditions such as temperature and time resulted in variations of the final compositions of the products, which consisted of mixtures of Mo(C,N,O)x, MoO2, Mo2C, Mo2N, and Mo. We optimized the reaction conditions to obtain carbide-rich phases. When evaluated as an anode material for application in lithium-ion battery half-cells, one of the optimized materials shows a remarkably high capacity of 933 mA h g−1 after 500 cycles. The maximum capacity is reached after an activation process caused by various conversion reactions with lithium.